|
NEW PRODUCTS
"Set in One" Apple Boxes were specifically designed for use where space is
at a premium, such as small location vans and small studios. A "Set in
One" is a complete set (1- Full, 1- Half, 1- Quarter and 1- Eighth) of Apple Boxes
that take up the same amount of space as just 1- standard Apple Box. Made from the
same materials as our standard Apple Boxes, but without the center support. All 4
sides are made of 3/4" Birch Plywood with the top and bottom made of 1/2" Birch
Plywood. We put a removable front on the "Set in One", which is kept in
place by two locating pins and two very strong "rare earth" magnets so that the
internal boxes don't come sliding out when the vehicle makes a turn. The entire set
can be carried from the single handhold on the open side of the full apple box, without
the front coming off.
"Set in One" Dimensions are:
Full: 12"x20"x8"
Half: 10-1/4"x18-1/4"x4"
Quarter: 10-1/4"x18-1/4"x2"
Eighth: 10-1/4"x18-1/4"x1"
Please Note:
We recommend that these boxes, as all Apple Boxes be treated with a wood sealer
to prevent excessive warping. Due to EPA regulations we are not able to do that at
the factory.
|
Position markers are made of 1-1/4"
Polypropelene Webbing filled with Stainless Steel Shot. They are approximately
6" long and have a #2 Nickle Plated Grommet at the top. Available in Teal,
White, Blue, Gold, Green, Black, Yellow and Red.
CLICK HERE
FOR PRICING
|
Position "T" Markers are made of
1-1/4" Polypropelene Webbing filled with Stainless Steel Shot. They are
approximately 6" long and have a #2 Nickle Plated Grommet at the top.
CLICK HERE
FOR PRICING
|
They are so easy to use and so comfortable. Almost like an
old, broken in pair of bedroom slippers. Made in all popular fabrics, Advantage
Gripware SLIPPERS will fit on practically any standard 48"x48" frame. The
elastic corners make it easy to mount and the 8- "hook & loop" tabs give it
tension. SLIPPERS come with a water resistant Orange pouch on which a list of the
contents can be marked with a "Sharpie." A grommet in the corner of the
pouch allows all SLIPPERS to be linked together with a cable tie, a piece of sash cord or
light chain.
Besides the standard fabrics, we have added some specials:
 | A Checkerboard Lame with 6" Squares instead of the usual
12" Squares |
| 4 Sided UltraBounce Floppy SLIPPER which can be used as a Video
Viewing Enclosure. |
| Underwater Black SLIPPER which can be used as a rain
shield over lighting fixtures. |
Any of the non "shoot through"
SLIPPERS can be used on Skinned Frames without the use of the "hook & loop"
tabs.
Frames Not Included.
CLICK HERE
FOR PRICING
|
Our new Butterfly Canopies are made of fire
retardant Ultra Bounce. To set up, take the Butterfly Canopy out of its included
storage bag and rig on a 6'x6' or 8'x8' Butterfly Frame depending on the size canopy being
utilized, as you would an ordinary Butterfly. Be sure that the white side is
up. Once the string ties are fastened, raise the stands and your Canopy is ready for
use. Set up time for one grip is approximately 5 minutes. One end of the
Butterfly Canopy is zippered which allows that end to be opened so that the video control
technician can see the set. That side can also be rigged on two
"C-Stands" to provide a sun shade. On each side of the Butterfly Canopy
there is a vent window that can be opened to allow air to circulate. A
"door" flap opposite the end that opens, allows easy entry. Butterfly
Canopies are made in 6'x6' and 8'x8'.
Butterfly Canopies also make great Dressing Rooms
on location or in the studio.
CLICK HERE FOR
PRICING |
30"x36" Cutter has three "floppy sides" with
Hook & Loop in each corner (1) so that any side can be opened for
greater viewing angle. A Hook & Loop closure in the center (2)
allows cables to be brought through. Made of Ultra Bounce material, making it
relatively light weight and with the white side out, will reflect some heat.
A pipe hem is provided for the 4 included Stainless Steel Tubes (3)
to provide stability and weight at the bottom.
CLICK HERE
FOR PRICING |
| WEDGES |
Camera Wedges (1"x3/4"x5")
|
Track Wedges (2x4x11-3/4")
|
Track Wedges (2x4x11-3/4") Milk Crate of 70
CLICK HERE FOR
PRICING |
Shelf Keeper hook directly into slots of
metal shelving |
Shelf Keeper attached to 2x4 shelf support |
Shelf Keeper Vinyl ID Pocket |
Shelf Keepers are designed to keep equipment on truck shelves while
in transit. The "cam-buckle" releases easily to drop or remove the shelf
keeper when access to the shelf is needed. Shelf Keepers can be used on trucks that
are shelved out with metal supports or with 2x4 supports. The clear vinyl ID pocket
will hold 3x5 card which can identify the items on the shelf. Pocket can be moved
anywhere along the length of the Shelf Keeper. Shelf Keepers are made in two Heights
10" and 15" and for 4', 5', 6' and 8' long shelves. We will be happy to
quote on custom sizes, please call customer service with your specifications.CLICK HERE FOR
PRICING |
 TM
|
ChromaTexTM is custom made for
Advantage Gripware and incorporates a flocked polyester face fabric similar to PolyPro
with the foam backing of Veltex, but with much greater consistency. The back
of the fabric is black to avoid creating uncontrolled
ambient bounce.
CLICK HERE FOR PRICING
|
 TM
|
After getting too many requests from our customers to ignore, we have finally given in and
are introducing our Popular ChromaTex Screens in a Back to Back Chroma Key Green /
Chroma Key Blue Screen version. ChromaTex Back to Back Screens are available in all
standard sizes as well as custom sizes.
CLICK HERE FOR PRICING
|
|
Avenger
Gripware, Inc. 2000 - 2009. All rights reserved.